Fluid mechanics lab

Product Details:

The set-up consists of different pressure measurement devices fitted in a pipe line, in which an Orifice is  fitted to create the pressure difference. Present set-up is self-contained water re-circulating unit, provided with a sump tank and a centrifugal pump etc. Flow control valve and by-pass valve are fitted in water line.

 

Additional Information:

• Item Code: IRE-201
• Delivery Time: 40 DAYS

Product Details:

The equipment is self-contained and is close circuit system.  It consists of two test sections, one for pipe surge and other for water hammer phenomenon. The whole system incorporates a head tank, measuring tank, sump tank,

circulating pump, a lever operated gate valve and flow control valve. The water enters the test pipe via the constant head tank and discharges into the measuring tank.Two electronic Pressure sensors with current output of 4 –20mA are installed on the unit.

The present set-up has a facility to interface the system with computer which enables to log the experimental data using computer. The educational software and data-logging package has been developed for unit. The software environment base is of Labview of NATIONAL INSTRUMENTS, USA. This software is compatible to interfacing unit designed by K. C. Engineers. This software package provides a comprehensive educational software environment within which the investigations can be performed. This software is capable to tabulate the sample readings according to the requirement of experiment under study and results obtained can be compared. The real time data acquisition can be done by interfacing the set-up with computer using software. Software allows the user to have control on data logging, printing the stored data, preparing spread sheets in Excel etc.

Additional Information:

• Item Code: IRE-121
• Delivery Time: 40 DAYS

Product Details:

The Unit consists of a strong cylinder containing fluid. A water cooled coil in the upper part of the cylinder condenses the vapour and return sit to the boiling liquid. The condenser cooling water rate can be measured and controlled also

Additional Information:

• Item Code: IRE-BHTU
• Production Capacity: 10
• Delivery Time: 30 DAYS
• Packaging Details: WOODEN CRATE

Product Details:

The equipment is designed and fabricated to demonstrate the Bernoulli's theorem. It consists of a test section made of acrylic. It has convergent and divergent sections. Pressure tapings are provided at different locations in convergent and divergent section. Present set-up is self-contained water re-circulating unit, provided with a sump tank, centrifugal pump etc. An arrangement is done to conduct the experiment on different flow rates. Flow rate of water is measured with the help of measuring tank and stopwatch.

Additional Information:

• Pay Mode Terms: L/C (Letter of Credit),T/T (Bank Transfer)
• Port of Dispatch: delhi
• Packaging Details: Wooden crates

Product Details:

The present Centrifugal Pump Test Rig is a self-contained unit operated on closed circuit basis containing a sump tank. The setup consists of a Centrifugal pump coupled with an AC Motor. Flow of water is measured by using measuring tank and stopwatch. Vacuum gauge is fitted on suction line and Pressure gauge is fitted on delivery line to measure the pressure

Additional Information:

• Item Code: IRE-1118
• Delivery Time: 35
• Packaging Details: YES

Product Details:

The present Submersible Pump Test Rig is a self-contained unit operated on closed circuit basis containing a sump tank. The set-up consists of a Submersible Pump, which is mounted horizontally with sump tank. Flow of fluid is measured by using measuring tank and stop watch.

Product Details:

Francis Turbine is a reaction turbine, which was developed by an English born American Engineer Sir J. B. Francis. The water enters the turbine through the outer periphery of the runner in the radial direction and leaves the runner in axial direction and hence it is called a mixed flow turbine. As the water flows to the runner, a part of pressure energy goes on changing into kinetic energy. Thus the water through the runner is under pressure. The runner is completely enclosed in a air tight casing and the casing & runner is always full of water. The present set-up consists of a runner. The water is fed to the turbine by means of Centrifugal Pump, radically to the runner. The runner is directly mounted on one end of a central SS shaft and other end is connected to a brake arrangement. The circular window of the turbine casing is provided with a transparent acrylic sheet for observation of flow on to the runner. This runner assembly is supported by thick cast iron pedestal. Load is applied to the turbine with the help of brake arrangement so that the efficiency of the turbine can be calculated. A draught tube is fitted on the outlet of the turbine. The set-up is complete with guide mechanism. Pressure and Vacuum gauges are fitted at the inlet and outlet of the turbine to measure the total supply head on the turbine.

Additional Information:

• Item Code: IRE-115
• Delivery Time: 35

Product Details:

The apparatus consists of a Nozzle meter made of stainless steel houses in Acrylic Test Section. Present set-up is self-contained water re-circulating unit, provided with a sump tank and a centrifugal pump. Flow control valve and by-pass valve are fitted in water line to conduct the experiment on different flow rates. Flow rate of water is measured with the help of measuring tank and stop watch.

Additional Information:

• Item Code: IRE-30
• Production Capacity: NA
• Delivery Time: 40 DAYS
• Packaging Details: YES

Product Details:

The setup consists of a clear Acrylic fabrication section. Water is fed through  a nozzle and discharged vertically to strike a target carried on a stem, which  extends through the cover. A weight carrier is mounted on the upper end of  the stem. The dead weight of the moving parts is counter balanced by a compression spring. The vertical force exerted on the target plate is measured for applied weights. Two targets cups are provided with the setup (flat plate and hemispherical cup).

Additional Information:

• Item Code: IRE-37
• Delivery Time: 40 DAYS
• Packaging Details: YES

Product Details:

The setup consists of 2 pipes of different diameters, which are connected in parallel. Pressure tapings are provided on each pipe to measure the pressure losses with the help of a Differential  Manometer. Control valves are fitted on each pipe, which enables to use one pipe at a time for experiment. Present set-up is self-contained water re-circulating unit, provided with a sump tank and a centrifugal pump etc. Flow control valve And by-pass valve are fitted in water line to conduct the Experiment on different flow rates. Flow rate of water is measured with the help of measuring tank and stop watch.

 

Additional Information:

• Item Code: IRE-38
• Production Capacity: NA
• Delivery Time: 40 DAYS
• Packaging Details: YES

Product Details:

The apparatus consists of two pipelines emerging out from a common manifold.  One pipe line contains a Venturimeter and other contains an Orifice. The pressure tapings from the Venturimeter and orifice meter are taken to differential manometer to measure pressure difference. The Venturimeter and Orifice meter are connected in parallel and any one of them can be put in operation by operating valves provided at the downstream. The flow can also be regulated by these valves.  Present set-up is self-contained water re-circulating unit, provided with a sump tank and a centrifugal pump etc. Flow control valve and by-pass valve are fitted in water line to conduct the experiment on different flow rates. Flow rate of water is measured with the help of measuring tank and stop watch

Additional Information:

• Item Code: IRE-41
• Production Capacity: NA
• Delivery Time: 40 DAYS

Product Details:

The apparatus consists of three pipelines emerging out from a common manifold.  One pipe line contain a Venturimeter, second contains an Orifice and third pipe line contains a Rota meter. The pressure tapings from the Venturimeter and Orifice meter are taken to differential manometer to measure pressure difference. The Venturimeter, Orifice meter and Rota meter are connected in parallel and any one of them can be put in operation by operating valves provided at the downstream. Present set-up is self-contained water re-circulating unit, provided with a sump tank and a centrifugal pump. Flow control valve and by-pass valve are fitted in water line to conduct the experiment on different flow rates. Flow rate of water is measured with the help of measuring tank & stop watch.

Additional Information:

• Item Code: IRE-42
• Delivery Time: 40 DAYS

Product Details:

 

The lab set up consists of a channel with deepened entry section having sufficient length and width in which water is supplied from the bottom .Required Notch is fitted a to need of this channel. Upstream from the face Notch, a gauge well is provided where a hook gauge is fitted. Arrangement for fixing interchangeable notches is made. Set of 3brass notches, i.e. rectangular notch, 600V notch & 450 V notch is provided along with the set-up. The set-up can be connected to Hydraulic Bench with flexible pipe line.

Additional Information:

• Item Code: IRE-FON5
• Production Capacity: 10
• Delivery Time: 30 DAYS

Product Details:

It consists of a tank provided within let supply diffuser, over flow outlet. Provision for fitting Orifice or Mouthpiece at the same position is provided. An arrangement is done to vary head and keep it constant at desired level .A Hook/pointer gauge arrangement for measuring X-Y co-ordinates of Jet Trajectory is also fitted. The set-up can be connected to Hydraulic Bench by flexible pipe line.

Additional Information:

• Item Code: IRE-OM65
• Production Capacity: 9
• Delivery Time: 30 DAYS

Product Details:

The set up consists of a two sided clear fabrication section .Water is fed through a nozzle and discharged vertically to strike a target carried on a stem which extends through the cover. A weight carrier is mounted on the upper end of the stem. The dead weight of the moving parts is counter balanced by a compression spring. The vertical force exerted on the target plate is measured by adding the weights supplied to the weight pan until the mark on the weight pan corresponds with the level  gauge .A total of two targets  are provided, a flat plate and a hemispherical cup.

Additional Information:

• Item Code: IRE-1232
• Production Capacity: 10
• Delivery Time: 30 DAYS

Product Details:

A Pitot tube is used to measure the local velocity at a given point in the flow stress. A Pitot tube of standard design made of copper /Stainless Steel is supplied and is fixed below a vernier scale. The vernier scale is capable to measure the position of Pitot tube in transparent pipe section. The pipe has a flow control valve to regulate the flow. An U-tube manometer is provided to determine the velocity head.

Additional Information:

• Item Code: IRE-PTS12
• Production Capacity: 10
• Delivery Time: 30 DAYS
• Packaging Details: WOODEN CRATE

Product Details:

This apparatus is useful for measurement of power transmitted for various input power conditions with varied belt tension. Belt slip or creep also can be measured. The apparatus consists of a variable speed motor, driving pulley and driven pulley of equal diameters. The pulleys are mounted on input shaft (motor shaft) and output shaft. The driven pulley can slide on the base only with bearing block to change the initial tension in belt. Brake drum is mounted on the output shaft, which helps to measure power output. The motor speed is varied by variable speed drive. A double channel digital speed indicator indicates driving and driven pulley speeds. With the help of Stroboscope (optional) it is possible to demonstrate the slip of belt on driving and driven pulley

Additional Information:

• Item Code: IRE-SCM-45
• Production Capacity: 10
• Delivery Time: 30 DAYS

Product Details:

The apparatus consists of a glass tube with one end having bell mouth entrance; connected to a constant head water tank, at the other end a valve is provided to vary the flow rate. The tank is of sufficient capacity to store water. A capillary tube is introduced centrally in the bell mouth for feeding dye from a small container placed at the top of tank, through polythene tubing. By varying the rate of flow, the Reynolds’s number is changed. This also changes the type of flow. Visual observation of dye (Thread) will indicate the type of flow, which can be confirmed from the Reynolds’s number computed. Present set-up is self-contained water re-circulating unit, provided with a sump tank and a centrifugal pump etc. Flow control valve and by-pass valve are fitted in water line. Flow rate of water is measured with the help of measuring cylinder and stop watch.

Additional Information:

• Item Code: IRE-43
• Delivery Time: 40 DAYS

Product Details:

The present set-up is designed to visualize the ideal flow around immersed body. It consists of a flow table in which flow of water is circulated in between two transparent sheets with a small gap between them. Water is supplied to the table and a colored dye is injected in the inlet of flow at different location. Water from the sump tank is pumped by a centrifugal pump to a calming section for table and after passing through transparent sheet it goes to sump tank. By-pass and flow control valves are provided to regulate the flow.Flow is made laminar by operating inlet control valve for water and it is visualized due to transparent sheet and colour. A small capacity dye tank will be provided for the flow of dye in fluid inlet stream. Any obstacle can be placed between the sheets and change in flow pattern can be visualized. Obstacles of different types will be supplied with the apparatus.

Additional Information:

• Item Code: IRE-49
• Delivery Time: 40 DAYS

Product Details:

The Centre of Pressure Apparatus has been designed to determine the static thrust exerted by a fluid on a submerged surface and allow comparison of the measured magnitude and position of this force with simple theory.A fabricated quadrant is mounted on a balance arm, which pivots on knife-edges. The knife-edges coincide with the centre of arc of the quadrant. Thus, of the hydrostatic forces acting on the quadrant when immersed, only the force on the rectangular end face gives rise to a moment about the knife-edges. The balance arm incorporates a balance pan for the weights supplied and an adjustable counterbalance. This assembly is mounted on top of an acrylic tank, which may be leveled by adjusting screwed feet. An indicator attached to the side of the tank shows when the balance arm is horizontal. Water is admitted to the top of the tank by a flexible tube and may be drained through a cock in the side of the tank. The water level is indicated on a scale on the side of the quadrant.

Additional Information:

• Item Code: ire-200
• Delivery Time: 40 days

Product Details:

The present set-up is designed to study the friction head losses through pipes, fittings, and flow metering devices. Four different ID sizes smooth pipes and one artificially roughened pipe is connected in parallel. A valve arrangement is provided to operate the one pipe at a time. Various types of fitting are also fitted with pressure taps to conduct the experiment. Flow meters (Venturimeter and Orificemeter) is also accompanies the set-up. For water circulation and flow rate determination sump tank & measuring tank are provided. The educational software and data –logging package has been developed for this unit. It is compatible to interfacing unit designed by KC Engineers. It provides a comprehensive educational software environment within which the investigations can be performed. This software runs in Windows XP. It is capable to tabulate the samples readings according to requirement of experiment under study and results obtained can be compared. Interfacing the set up with computer using software can do the real time data acquisition. Data can be transferred in Excel Files for further calculations, plotting graphs etc. Software allows the user to have control on data logging, printing the stored data, preparing spread sheets in Excel etc.

Additional Information:

• Item Code: ire-333
• Delivery Time: 40 days

Product Details:

Hydraulic Ram is used for pumping small quantity of water at high head, when large quantity of water at small head is available. It operates on the principle that if flowing water is suddenly brought to rest in a long pipe, a phenomena known as water hammer occurs, wherein a pressure wave travels along the pipe. This principle is used in the Hydraulic Ram to pump water. The set-up consists of a box incorporating pulse and non-return valves and a supply reservoir on a stand which is fed by the overhead tank. An air vessel above the valve chamber smoothes cyclic fluctuations from the Ram delivery. Different pressure may be applied to the pulse valve to change the closing pressure and hence the operating characteristic