Product Details:
Minimum Order Quantity | 1 Piece |
Filtration Capacity | 40 liter/hr |
Body Material | acrylic |
Country of Origin | Made in India |
Material | acrylic |
Color | Blue |
Diameter | 200 mm x 200 mm |
Voltage | 220v ac |
Capacity | 40 liter/hr |
Usage/Application | LAB EXPERIMENT |
No Of Plates | 1 phase |
Pressure filters can apply a large pressure differential across the septum to give economically rapid filtration with viscous liquids or fine solids. The most common types of pressure filters are filter press. A filter press contains a set of plates designed to provide a series of chambers or compartments in which solids may collect. The plates are covered with a filter medium such as canvas cloth. Slurry is admitted to each compartment under pressure; liquor passes through the canvas cloth and out a discharge pipe, leaving a wet cake of solids behind. Plates and frames sit horizontally in a metal rack, with cloth covering the face of each plate, and are squeezed tightly together by a screw. Slurry enters at one end of the assembly of plates and frame. It passes through a channel running lengthwise through one corner of assembly. The set up consists of 7 plates and 6 frames. Frames are covered with filter cloth. Feed is fed by gear pump at the top and filtrate collected at the bottom from each plate by operating the cock.After removing Cake, washing and cleaning can be done by water provided by overhead tank. Inlet & outlet pressures are measured by pressure gauges. Rate of filtrate removals is measured by calibrated tank provided.
Additional Information:
Product Details:
Minimum Order Quantity | 1 Piece |
Model Name/Number | IRE-GSS5 |
Color | BLUE |
Voltage | 220V |
Warranty | 1 YEAR |
I Deal In | New Only |
Power | 220V |
Brand | INNOVATIVE RESEARCH EQUIPMENT |
Country of Origin | Made in India |
Motor Type | By 1/2 HP motor |
Gyratory type shaker is driven by FHP motor through a reduction gear suitable to carry upto 7 sieves of 20 cm diameter. When clamped the sieve table does not rotate but it is inclined from the vertical axis and the direction of inclination changes progressively in the clockwise direction.
In addition to the gyratory motion of the shaker, there is an upward and downward movement ensuring that each square inch of the sieve is utilised. The whole mechanism runs in an oil bath. Test Sieves will be supplied at an extra cost
Additional Information:
Product Details:
Minimum Order Quantity | 1 Piece |
Diameter | Size: 200 mm x 200 mm |
Country of Origin | Made in India |
Usage/Application | LAB EXPERIMENT |
Color | Blue |
Voltage | 220v ac |
Filtration Capacity | 50 liter |
Capacity | 40 liter/hr |
No Of Plates | 7 |
Material | acrylic |
Pressure filters can apply a large pressure differential across the septum to give economically rapid filtration with viscous liquids or fine solids. The most common types of pressure filters are filter press. A filter press contains a set of plates designed to provide a series of chambers or compartments in which solids may collect. The plates are covered with a filter medium such as canvas cloth. Slurry is admitted to each compartment under pressure; liquor passes through the canvas cloth and out a discharge pipe, leaving a wet cake of solids behind. Plates and frames sit horizontally in a metal rack, with cloth covering the face of each plate, and are squeezed tightly together by a screw. Slurry enters at one end of the assembly of plates and frame. It passes through a channel running lengthwise through one corner of assembly. The set up consists of 7 plates and 6 frames. Frames are covered with filter cloth. Feed is fed by gear pump at the top and filtrate collected at the bottom from each plate by operating the cock.After removing Cake, washing and cleaning can be done by water provided by overhead tank. Inlet & outlet pressures are measured by pressure gauges. Rate of filtrate removals is measured by calibrated tank provided.
Additional Information:
Product Details:
Minimum Order Quantity | 1 Piece |
Material | Stainless Steel |
Model Name/Number | IRE-PDPB-2 |
Color | GRAY |
Brand | INNOVATIVE RESEARCH EQIPMENT |
Capacity | 30 LTR |
Country of Origin | Made in India |
Usage/Application | LAB EXPERIMENT |
Phase | Single Phase |
Size | rings Size 8-10mm |
The set-up consists of a glass column packed with packing material i.e. Ranching rings, SS mesh to support the packing and with calming section. Pressure drop across packed bed can be measured by a manometer. The apparatus is close circuit type provided with tank, Pump, necessary piping, valves and Rota meter to measure the flow rate of fluid. The set-up is fitted on a MS frame and painted with good quality corrosion resistant paint.
Additional Information:
Product Details:
Minimum Order Quantity | 1 Piece |
Material | Stainless Steel |
Brand | Innovative Research Equipments |
Power Source | Electric |
Phase | Single Phase |
Frequency | 50 Hz |
Additional Information:
Product Details:
Minimum Order Quantity | 1 Piece |
Power | 220v AC |
Weight | na |
Phase | single |
Usage/Application | Laboratory |
Drive Power | 1 HP, variable speed motor and Drive, coupled to Reduction Gearbox. |
Type | lab experiment |
Material | Stainless Steel |
Ring Diameter | 275mm |
Capacity | na |
Ball Mills are horizontal rotating cylindrical steel chamber of half filled with steel balls. The size reduction is accomplished by the impact of balls as they fall back after being lifted by the baffles fitted in the rotating chamber.Ball Mill is fitted on a sturdy MS frame. Charging of balls and material is done by the means of opening provided in the chamber. The chamber is turning about the horizontal axis through a reduction gearbox drive through 1 HP variable speed motor. Drive is provided to vary the RPM. A RPM indicator with proximity switch is provided in the set-up. A revolution counter is provided to find out the number of turns. Special arrangement is done to free the Ball Mill from reduction gearbox for charging and discharging the material.
Additional Information:
Product Details:
Minimum Order Quantity | 1 Piece |
Usage/Application | laboratory |
Usage | lab experiment |
Leaf Filter Diameter | 200mm with SS Mesh & filter cloth on both sides. |
Electric Supply | 220v |
Floor Area | 1m x 1.5m |
Body Material | stainless steel |
Capacity | 50 ltr |
Country of Origin | Made in India |
Additional Information:
Product Details:
Minimum Order Quantity | 1 Piece |
Dimension | Dia 275mm, Length 350mm. Thickness 5 mm |
Country of Origin | Made in India |
Usage/Application | Laboratory |
Ring Diameter | 275mm |
Material | Mild Steel |
Phase | single |
Power | 220v AC |
I Deal In | New Only |
Drive Power | 1 HP, variable speed motor and Drive, coupled to Reduction Gearbox. |
Ball Mills are horizontal rotating cylindrical steel chamber of half filled with steel balls. The size reduction is accomplished by the impact of balls as they fall back after being lifted by the baffles fitted in the rotating chamber. Ball Mill is fitted on a sturdy MS frame. Charging of balls and material is done by the means of opening provided in the chamber. The chamber is turning about the horizontal axis through a reduction gearbox and three step pulley connected to a motor. The stepped pulley arrangement is done for moving the Ball Mill at three different speeds. A revolution counter is provided to find out the number of turns. Special arrangement is done to free the Ball Mill from reduction gearbox for charging and discharging the material.
Additional Information:
Product Details:
Minimum Order Quantity | 1 Piece |
Material | Stainless Steel |
Phase | Single Phase |
Model Name/Number | IRE-T3 |
Color | BLUE |
Dimensions | Dia. 200-mm, Length 750-mm (approx.) |
Country of Origin | Made in India |
Brand | INNOVATIVE RESEARCH EQIPMENT |
Usage/Application | LAB EXPERIMENT |
Trammel or revolving screens consists of a cylindrical screen rotated about its axis. Simple Trammel may be arranged in series with oversize of the first passing to the second Trammel and the oversize of the second passing to the third, etc. They are quite efficient for coarse sizes. The inclination of Trammel varies depending on the nature of material to be processed. The present Trammel is built with screens of different sizes throughout their length, the feed entering at the end of the finest screen. In this way it is possible to collect materials of different size range from a single Trammel. Drive to the central shaft is given through a motor coupled to reduction gearbox. Set-up is complete in all respect with guards, bins and control panel. A special arrangement to change the angle of inclination of the Trammel is made.
Additional Information:
Product Details:
Minimum Order Quantity | 1 PIECE |
Type Of Machine | Mineral Jig Machine |
Motor Power | FHP PUMP |
Country of Origin | Made in India |
Material | Stainless Steel |
Current | 220V |
Usage/Application | LAB EXPERIMENT |
Voltage | 220V |
Capacity | 10 LTR |
Floor Area | 1.5 m x 1 m. |
Tank Capacity | 10 LTR |
A jig is a mechanical device used for separating materials of different specific gravity by the pulsation of a stream of liquid flowing through a bed of material. The setup consists of plunger operated by crank mechanism connected to motor coupled with reduction gear box. Sump tank with pump is provided for water circulation.
Additional Information:
Product Details:
Brand | INNOVATIVE RESEARCH EQUIPMENTS |
Usage/Application | lab equipment |
Material | Stainless Steel |
Phase | Single Phase |
Model Name/Number | IRE51 |
Country of Origin | Made in India |
india | 65000 |
An Elutriator is vertical tube through which a fluid passes upwardly at a specific velocity while a solid mixture, whose separation is desired, is fed into the top of the column. The large particles, which settle at a velocity higher than that of the rising fluid, are collected at the bottom of the column, and the smaller particles are carried out of the top of the column with the fluid. Several columns of different diameters in series may be used to bring about a further separation. The set up consists of two vertical tubes of different diameter in which water is passed at a controlled velocity. A tank with pump is provided for re-cycled water supply and flow rate is measured by Rota meter and controlled with the help of control valve. The tubes are arranged in a fashion of ascending cross-section area. The particles are introduced through a feed hopper provided at first tube, the smaller particles are carried over in the fluid stream, while the large particles settle against the upward stream. The overflow from the first tube introduced at the bottom of second tube is passed vertically upwards and the overflow from the second tube introduced at the, is passed to drain. The weighed sample originally placed in the first tube of smallest diameter is classified into fractions according to their settling velocities. The fractions are collected in successive tubes by a special arrangement and may be dried and weighed to make analysis.
Additional Information:
Product Details:
Minimum Order Quantity | 1 Piece |
Country of Origin | Made in India |
Material | STAINLESS STEEL |
Voltage | 220V |
Capacity | 40 - 100 |
Type | LAB EXPERIMENT |
Brand | INNOVATIVE RESEARCH EQUIPMENT |
I Deal In | New Only |
Cone types Classifiers are one of the oldest types. The conical vessel has angle of 60o. The feed is fed from the top. Water is passed at a controlled velocity. The coarse solids travel down the sides and can be removed from the bottom. Fine particles are separated by over flow. Bottom product tank is provided with the setup.
Additional Information:
Product Details:
Minimum Order Quantity | 1 Piece |
Color | Blue |
Power | 220v |
Country of Origin | Made in India |
Material | Stainless Steel |
Diameter | 75mm |
Usage/Application | LAB EXPERIMENT |
Length | 725mm |
Application/Usage | LAB EXPERIMENT |
I Deal In | New Only |
Voltage | 220v |
Motor Power | 1/2 H.P. motor coupled to a Reduction |
Warranty | 1 year |
Additional Information:
Product Details:
Minimum Order Quantity | 1 Piece |
Diameter | 72 mm |
Phase | Single Phase |
Operating Voltage | 220V AC |
Brand | Innovative Research Equipments |
Floor Area | 1.5 m x 0.75 m |
Material | Stainless Steel |
Current | 5-15 amp |
Sump Tank Capacity | 50 L |
The set-up consists of a cylindrical test section filled with pourous medium. Pressure tappings are provided in the test section to measure the pressure drop with the help of differential manometer. Present set-up is self-contained water re-circulating unit, provided with a sump tank and a centrifugal pump etc. Flow control valve and bypass valve are fitted in water line to conduct the experiment on different flow rates. Flow rate of water is measured with the help of measuring tank and stop watch.
Additional Information:
Product Details:
Minimum Order Quantity | 1 Piece |
Power | 220V AC 1 PHASE |
Application | LAB EXPERIMENT |
Country of Origin | Made in India |
Brand | INNOVATIVE RESEARCH EQUIPMENT |
Model | IRE-FF-5 |
Capacity | 20 LTR |
Type | NA |
Mixed liberated particles can be separated from each other by floatation if there is sufficient difference in their wet ability. The floatation process operates by preparing a water suspension of a mixture of relatively finely sized solids. This is usually done in an agitated chamber open at the top. Fine bubbles of air are then dispersed through the agitated suspension to form a froth that rises to the top of the chamber. Particles that are radically wetted by water (hydrophilic) tend to remain in the water suspension. Those particles that are not easily wetted (hydrophobic) tend to be collected at the air bubble-water interface and rise to the surface attached to air bubbles. Thus differences in the surface chemical properties of the solids are the basis for separation. The set up consists of a agitated chamber open at the top. In the chamber, an impeller coupled to a shaft is fixed in a stationary diffuser. Low-pressure air is allowed to enter in the stationary diffuser through the air passage provided with the agitator. The collector coated mineral particles adhere to the rising bubbles and are carried to the top of the cell to be removed in the froth product.
Additional Information: