Laboratory Apparatus

Product Details:

Aimed at prosperous growth in this domain, we are instrumental in offering an excellent quality range of Composite Wall Apparatus.

Product Details:

Ball Mills are horizontal rotating cylindrical steel chamber of half filled with steel balls. The size reduction is accomplished by the impact of balls as they fall back after being lifted by the baffles fitted in the rotating chamber.Ball Mill is fitted on a sturdy MS frame. Charging of balls and material is done by the means of opening provided in the chamber. The chamber is turning about the horizontal axis through a reduction gearbox drive through 1 HP variable speed motor. Drive is provided to vary the RPM. A RPM indicator with proximity switch is provided in the set-up. A revolution counter is provided to find out the number of turns. Special arrangement is done to free the Ball Mill from reduction gearbox for charging and discharging the material.

Additional Information:

• Item Code: yes
• Pay Mode Terms: L/C (Letter of Credit),T/T (Bank Transfer)
• Port of Dispatch: delhi
• Production Capacity: 10 ltrs
• Delivery Time: 30 days
• Packaging Details: as per demand

Product Details:

The apparatus consists of blower unit fitted with the test pipe. Nichrome Wire heater surrounds the test section.  Four Temperature Sensors are Embedded on the test section, two placed in the air stream at the entrance and exit of the test section to measure the inlet and outlet air temperature. Test pipe is connected to the delivery side of the blower along with the orifice to measure flow of air through the pipe. Constant heat flux is given to pipe by an electric heater through a variac and measured by Digital Voltmeter and Digital Ammeter.

 

Product Details:

The present Centrifugal Pump Test Rig is a self-contained unit operated on closed circuit basis containing a sump tank. The set-up consists of a Centrifugal pump coupled with a swinging frame type DC Motor which permits direct torque measurement with the help of a spring balance. Power input to the DC Motor is varied by means of a Thyristor controlled DC Drive to vary the RPM of motor. A RPM Indicator with Proximity sensor indicates the RPM of Pump. Flow of water is measured by using measuring tank and stop watch. Vacuum gauge is fitted on suction line and Pressure gauge is fitted on delivery line to measure the pressure.

 

Product Details:

The set-up is designed to study Coriolli's Component of Acceleration of a slider crank mechanism. Here the mechanical slider system is replaced by a continuous stream of water flowing through a steady rotating pair of tubes. These tubes can be rotated at various speeds by using a swinging field motor which also acts as dynamometer. A Perspex window on top of the tank gives clear view of the process and prevents splash of the water over the side of the tank. The dynamometer continuously measures torque applied to the rotating tubes. The equipments is self contained, water re-circulating, provided with its own speed control unit and water circulating pump.

Additional Information:

• Item Code: IRE-CCA-65
• Production Capacity: 10
• Delivery Time: 30 DAYS

Product Details:

Backed by rich industry experience, we are engaged in providing a premium quality range of Thermal Conductivity Apparatus.

Additional Information:

• Production Capacity: standard

Product Details:

Drainage & Seepage Tank Apparatus

The setup studies behavior of multi capacity process when connected in interaction mode. It consists of supply tank, pump for water circulation, Rotameter for flow measurement, two independent process tanks with scales connected in interacting mode. The components are assembled on frame to form tabletop set-up.

 

Additional Information:

• Item Code: IREDS02

Product Details:

The setup is designed to study the heat transfer in a pin fin. It consists of pin type fin fitted in a duct. A fan is provided on one side of duct to conduct experiments under forced draft conditions. Air flow rates can be varied. A heater heats one end of fin and heat flows to another end.  Heat input to the heater is given through Variac. Digital voltmeter and digital ammeter are provided for heat measurement. Digital Temperature Indicator measures temperature distribution along the fin.

Additional Information:

• Item Code: na
• Production Capacity: na
• Delivery Time: 30
• Packaging Details: yes

Product Details:

The set up is designed to study the whirling of shafts. The set-up consists of a sturdy frame, bearing holders, variable speed motor etc. to drive the shaft along with speed control unit.  Different bearing can be fitted in bearing block to have different end conditions i.e. (i) both end fixed, (ii) one end free and one end fixed etc. As the test is destructive, hence the shaft cannot be used again.

Additional Information:

• Item Code: IRE-WSD-5
• Production Capacity: 10
• Delivery Time: 30 DAYS

Product Details:

 

The apparatus provided comprehensive unit to perform the vibration experiments. A universal frame is provided upon which quick and easy assembly of various experiments can be done. The unit is self-contained to safely store spares. The students can easily assemble the experiments and study the theory of vibrations practically.

 

Additional Information:

• Item Code: IRE-UVA-6
• Production Capacity: 10
• Delivery Time: 30 DAYS

Product Details:

The present set-up is designed to study the characteristics of a U Tube manometer. It consists of a U Tube manometer, which is pressurized by air. A suitable and proper arrangement has done for charging and discharging the manometer fluid in the manometer. These arrangements facilitate to observe the response of different types of manometer fluids of different heights. An air pressure regulator is provided to change the pressure in the manometer. All components are assembled on a frame to form a table top set-up.

Additional Information:

• Item Code: IRE-TCM-22
• Production Capacity: 10
• Delivery Time: 30 DAYS

Product Details:

The set up consists of 3 glass columns. One column is provided with glass beeds for fluidization study. Two columns are packed with different packing’s, i.e. one filled with Rashing Rings and other one is filled with barrels addle. Pressure drop can be measured by manometer. The set up studies in fluidization characteristics and relationship between the velocity of the fluid and pressure dropper unit length. The apparatus is close circuit type provided with suitable capacity tank, FHP pump, necessary pipe line valves and a Rota meter to measure the flow rate of fluid . An valve arrangement is provided too sperate any single column at a time. The set up is fitted on a MS frame painted with good quality paint.

Additional Information:

• Item Code: IRE-FFB-65
• Production Capacity: 10
• Delivery Time: 30 DAYS

Product Details:

A Cyclone Separator is a vertical cylinder with the inlet stream introduced tangentially near the top, giving the suspension a spinning rotation in the cylinder. The centrifugal force acting on the particles tends to throw them radically to the sides of the cylinder as they spiral downward to a conical bottom where they are removed. A collector is fitted at the bottom & the induced draft blower is used to create the air stream. The classified air leaves the cyclone through a pipe extended down into the cyclone & passes through blower delivery side fitted with fine screen cloth bag to avoid dust expansion in the laboratory.The setup consists of I.D. blower connected to discharge side of Cyclone Separator. A flow meter with manometer is provided to measure the flow rate of air. Pressure drop in the Cyclone is measured by water manometer. Solids are collected in the collector fixed at the bottom. The set-up is complete with flow Control & by-pass valve.

Additional Information:

• Item Code: IRE-CS56
• Production Capacity: 10
• Delivery Time: 30 DAYS

Product Details:

The equipment consists Rotating Disc reactor units, It also consists of two Reactant tanks made up of Stainless steel and one thermal bath with fitted heater on it. Set up contains two rotameter one each for individual reactant. Control valves and by pass valves are provided in set up for better control of reactant during process.

Additional Information:

• Item Code: IRE-RDC3
• Production Capacity: 8
• Delivery Time: 30 DAYS
• Packaging Details: WOODEN CRATE

Product Details:

The present Set-up is designed to measure the emissivity of test plate. The test plate comprises of a mica heater sandwiched between two circular plates.  Black plate is identical with test plate, but its surface is blackened. As all the physical properties, dimension and temperature are equal; heat losses from both plates will be same except radiation loss. Hence the input difference will be due to difference in emissivity. Both plates are supported on individual brackets in a enclosure with one side glass to ensure steady atmospheric conditions. Temperature Sensors are provided to measure the temperature of each plate and surrounding. Electric Supply is given to heaters through separate variacs so that temperatures of both can be kept equal and is measured with Digital Voltmeter and Digital Ammeter.

Additional Information:

• Item Code: IRE-EMA12
• Production Capacity: 8
• Delivery Time: 30 DAYS

Product Details:

A pontoon is allowed to float in a small tank having a transparent side.  Removable steel strips placed in the model for the purpose of changing the weight of the model.  Displacement of weight is measured with the help of a scale. By means of a pendulum (consisting of a weight suspended to a long pointer) the angle of tilt can be measured on a graduated arc.For tilting the ship model, a cross bar with movable hanger is fixed on the model.  Pendulum and graduated arc are suitably fixed at the center of the cross bar.  A set of weights is supplied with the apparatus.

 

Additional Information:

• Item Code: IRE-54
• Delivery Time: 40 DAYS

Product Details:

The setup is designed to study the heat transfer in a pin fin. It consists of pin type fin fitted in a duct. A fan is provided on one side of duct to conduct experiments under forced draft conditions. Air flow rates can be varied. A heater heats one end of fin and heat flows to another end.  Heat input to the heater is given through Variac. Digital voltmeter and digital ammeter are provided for heat measurement. Digital Temperature Indicator measures temperature distribution along the fin.

Additional Information:

• Item Code: IRE-456
• Production Capacity: 10
• Delivery Time: 30 DAYS

Product Details:

The hydraulic bench is suitable for the use of basic fluid mechanics experiments of fluid mechanics. It supplies the water in the closed circuit; the determination of volumetric flow rate and the positioning of the experimental unit on the working surface of the base module and the collection of dripping water. The closed water circuit consists of the sump tank with the submersible pump and the measuring tank arranged above, in which the returning water is collected. The measuring tank is stepped, for large and smaller volumetric flow rates. A measuring cylinder is provided for very small volumetric flow rates. A stopwatch will also be provided for measuring the flow rate. The top surface should enable the various experimental units to be easily and safely positioned

Additional Information:

• Item Code: IRE-HB45
• Production Capacity: 8
• Delivery Time: 30 DAYS

Product Details:

The present setup is designed to study the critical heat flux of a given   nichrome   wire.   The   setup   consists   of   temperature controlled water bath with controller. Temperature of the water bath can be varied from ambient to 80°C to achieve different envioronment for nichrome wire. Test heater wire is placed in the bath & voltage is varied by variac provided. The system is complete with digital temperature controller, voltmeter, ammerter & voltage control facility.

Additional Information:

• Item Code: IRE-PB200
• Production Capacity: 10
• Delivery Time: 30 DAYS

Product Details:

The apparatus has been designed to demonstrate the phenomena of Cavitation. The present set-up consists of a test section made of Acrylic  having conversion and diversion section. Pressure tapings at appropriate position are provided. This test section is having one control valve at upstream side to regulate the water flow rate. Two pressure gauges are connected to these taping which give the pressure readout at the time of flow passing through this test section. The unit is self-contained close circuit type with sump tank, measuring tank and centrifugal pump. Flow through test section can be regulated with the help provided by-pass and control valve

Additional Information:

• Item Code: IRE-46
• Delivery Time: 40 DAYS

Product Details:

 

It consists of a tank provided with inlet supply diffuser, overflow. Provision for fitting Orifice or Mouthpiece at the outlet of tank. An arrangement is done to vary head and keep it constant at desired level. A pointer gauge arrangement for measuring X-Y co-ordinates of Jet is also fitted. Present set-up is self-contained water re-circulating unit, provided with a sump tank and a centrifugal pump etc.  Flow rate of water is measured with the help of measuring tank and stop watch.

Additional Information:

• Item Code: IRE-35
• Production Capacity: NA
• Delivery Time: 40 DAYS
• Packaging Details: YES